F436M ANSI Carbon Steel ZINC HDG BLACK Steel Flat Washer
Materials and Chemical compstition
|CHEMICAL COMPOSI %|
This specification covers the chemical, mechanical, and dimensional requirements for metric hardened steel washers for use with fasteners having nominal thread diameters M12 through M100.
Formerly under the jurisdiction of Committee F16 on Fasteners, this specification was withdrawn in September 2016 and replaced by Specificationfor Hardened Steel Washers Inch and Metric Dimensions.
1.1 This specification covers the chemical, mechanical, and dimensional requirements for metric hardened steel washers for use with fasteners having nominal thread diameters M12 through M100. These washers are intended for general-purpose mechanical and structural use with bolts, nuts, studs, and other internally and externally threaded fasteners. These washers are suitable for use with fasteners covered in Specifications A325M, A490M, A563Mand with fasteners of Specification F568M property classes 8.8 and higher.
1.2 The types of washers covered in this specification are:
1.2.1 Type 1—Washers made of carbon steel.
1.2.2 Type 3—Washers made of steel having atmospheric corrosion resistance and weathering characteristics comparable to that of steels covered in Specifications A242/A242M, A588/A588M, and A709/A709M. The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition. See 5.1. When properly exposed to the atmosphere, these steels can be used bare (uncoated) for many applications.
1.2.3 This specification provides for furnishing Type 3 to chemical composition or a Corrosion Resistance Index (CRI) of 6 or higher at the suppliers option.
1.3 The styles of washers covered in this specification are:
1.3.1 Circular Washers—Circular washers in nominal sizes 12 mm through 100 mm, are suitable for applications where sufficient space exists and angularity permits.
1.3.2 Beveled Washers—Beveled washers are square and rectangular, in nominal sizes 12 mm through 36 mm, with a beveled 1:6 surface for use with American Standard beams and channels.
1.3.3 Clipped Washers—Clipped washers are circular or beveled for use where space limitations necessitate that one side be clipped.
1.4 Terms used in this specification are defined in Terminology F1789 unless otherwise defined herein.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1—This specification is the metric counterpart of Specification F436.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately)
A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
A242/A242M Specification for High-Strength Low-Alloy Structural Steel
A325M Specification for Structural Bolts, Steel, Heat Treated 830 MPa Minimum Tensile Strength (Metric)
A490M Specification for High-Strength Steel Bolts, Classes 10.9 and 10.9.3, for Structural Steel Joints (Metric)
A563M Specification for Carbon and Alloy Steel Nuts (Metric)
A588/A588M Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance
A709/A709M Specification for Structural Steel for Bridges
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
D3951 Practice for Commercial Packaging
F436 Specification for Hardened Steel Washers
F568M Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Metric)
F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric)
F1136M Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners (Metric)
F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
F1789 Terminology for F16 Mechanical Fasteners
G101 Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
B 18.23.2M Metric Beveled Washers
50KG/ IRON DRUM,12 IRON DRUMS/PALLET
QBH SMALL PACKING
Packing in small boxes according to customer’s requirements
Packing in plastic bag according to customer’s requirements
QBH PALLET TYPE
SOLID WOOD FUMIGATION PALLET
THREE SPLINT PALLET
The advantages of QBH
- QBH brand sales to the main quality assurance.
- Years of export trade management, excellent service, word-of-mouth guarantee.
- By working with TUV,escort for quality.
- Customization of non-standard parts can be made according to customer's requirements and drawings.
- For quality customers,we can provide a certain credit period.